Follow Ups Full Thread

Topic - Paging olddude . . . - alaskahiatt 19:14:39 04/20/21 (26)

• RE: Paging olddude . . . - SgreenP@MSN.com 10:48:20 04/24/21 (0)
• RE: Paging olddude . . . - pictureguy 04/21/2122:30:34 04/21/21 (8)
• RE: I use a 9/32 in. drill bit. - tketcham 05:16:44 04/22/21 (6)
• The 9/32" drill bit is probably a good size for almost all spindles, but - alaskahiatt 11:52:01 04/22/21 (5)
• RE: The 9/32" drill bit is probably a good size for almost all spindles, but - tketcham 12:48:48 04/22/21 (4)
• AR was never a problem back in the day - Triode_Kingdom 12:08:16 04/3/25 (1)
• RE: AR was never a problem back in the day - Don Reid 07:12:03 04/4/25 (0)
• Fortunately, it has only happened about four times so far, but - alaskahiatt 14:05:43 04/22/21 (1)
• Oops, it happened again last night with Steely Dan "Countdown to Ecstasy." nt - alaskahiatt 10:28:29 04/24/21 (0)
• The NAB standard is .2830 inches or 7.1882mm as stated in the AR-XA manual. - alaskahiatt 00:35:52 04/22/21 (0)
• Be careful, I used to have one............ - Self-Inflicted 17:07:19 04/21/21 (3)
• $50 for one drill bit? Now, that is over the top. The drill is very close - alaskahiatt 22:27:29 04/21/21 (0)
• RE: Clearaudio LP drill - B. Scarpia 19:13:53 04/21/21 (0)
• No problem. I was nervous from the start, so I did a little at a time - alaskahiatt 17:30:18 04/21/21 (0)
• RE: Paging olddude . . . - George S. Roland 12:57:08 04/21/21 (0)
• Cool. But overkill? - Dave Pogue 05:50:08 04/21/21 (7)
• I used to use an X acto knife... - musetap 11:17:00 04/21/21 (0)
• The AR XA is unusually well-endowed. - ghost of olddude55 06:34:55 04/21/21 (5)
• RE: The AR XA is unusually well-endowed. - Dave Pogue 07:46:55 04/21/21 (4)
• Had a rat-tail file around here for a while... - ghost of olddude55 08:01:20 04/21/21 (3)
• RE: Had a rat-tail file around here for a while... - orthophonic 13:44:12 04/21/21 (2)
• You are correct, and here's page 10 of the AR-XA manual. - alaskahiatt 14:07:20 04/21/21 (0)
• The issue was primarily with new pressings. - ghost of olddude55 13:54:01 04/21/21 (0)
• Same one I have. - ghost of olddude55 04:06:32 04/21/21 (0)
• One of my favorites.... - alan m. kafton 01:50:40 04/21/21 (0)
• Interesting... had no idea there was a reaming tool... - musetap 22:18:04 04/20/21 (0)

Follow Ups

• RE: Paging olddude . . . - pictureguy 04/21/2122:30:34 04/21/21 (8)
• RE: I use a 9/32 in. drill bit. - tketcham 05:16:44 04/22/21 (6)
• The 9/32" drill bit is probably a good size for almost all spindles, but - alaskahiatt 11:52:01 04/22/21 (5)
• RE: The 9/32" drill bit is probably a good size for almost all spindles, but - tketcham 12:48:48 04/22/21 (4)
• AR was never a problem back in the day - Triode_Kingdom 12:08:16 04/3/25 (1)
• RE: AR was never a problem back in the day - Don Reid 07:12:03 04/4/25 (0)
• Fortunately, it has only happened about four times so far, but - alaskahiatt 14:05:43 04/22/21 (1)
• Oops, it happened again last night with Steely Dan "Countdown to Ecstasy." nt - alaskahiatt 10:28:29 04/24/21 (0)
• The NAB standard is .2830 inches or 7.1882mm as stated in the AR-XA manual. - alaskahiatt 00:35:52 04/22/21 (0)