$50 for one drill bit? Now, that is over the top. The drill is very close

Vinyl Asylum

Welcome Licorice Pizza (LP) lovers! Setup guides and Vinyl FAQ.

Follow Ups Full Thread

Topic - Paging olddude . . . - alaskahiatt 19:14:39 04/20/21 (26)

RE: Paging olddude . . . - SgreenP@MSN.com 10:48:20 04/24/21 (0)

RE: Paging olddude . . . - pictureguy 22:30:34 04/21/21 (8)

RE: I use a 9/32 in. drill bit. - tketcham 05:16:44 04/22/21 (6)

The 9/32" drill bit is probably a good size for almost all spindles, but - alaskahiatt 11:52:01 04/22/21 (5)

RE: The 9/32" drill bit is probably a good size for almost all spindles, but - tketcham 12:48:48 04/22/21 (4)

AR was never a problem back in the day - Triode_Kingdom 12:08:16 04/3/25 (1)

RE: AR was never a problem back in the day - Don Reid 07:12:03 04/4/25 (0)

Fortunately, it has only happened about four times so far, but - alaskahiatt 14:05:43 04/22/21 (1)

Oops, it happened again last night with Steely Dan "Countdown to Ecstasy." nt - alaskahiatt 10:28:29 04/24/21 (0)

The NAB standard is .2830 inches or 7.1882mm as stated in the AR-XA manual. - alaskahiatt 00:35:52 04/22/21 (0)

Be careful, I used to have one............ - Self-Inflicted 17:07:19 04/21/21 (3)

$50 for one drill bit? Now, that is over the top. The drill is very close - alaskahiatt 04/21/2122:27:29 04/21/21 (0)

RE: Clearaudio LP drill - B. Scarpia 19:13:53 04/21/21 (0)

No problem. I was nervous from the start, so I did a little at a time - alaskahiatt 17:30:18 04/21/21 (0)

RE: Paging olddude . . . - George S. Roland 12:57:08 04/21/21 (0)

Cool. But overkill? - Dave Pogue 05:50:08 04/21/21 (7)

I used to use an X acto knife... - musetap 11:17:00 04/21/21 (0)

The AR XA is unusually well-endowed. - ghost of olddude55 06:34:55 04/21/21 (5)

RE: The AR XA is unusually well-endowed. - Dave Pogue 07:46:55 04/21/21 (4)

Had a rat-tail file around here for a while... - ghost of olddude55 08:01:20 04/21/21 (3)

RE: Had a rat-tail file around here for a while... - orthophonic 13:44:12 04/21/21 (2)

You are correct, and here's page 10 of the AR-XA manual. - alaskahiatt 14:07:20 04/21/21 (0)

The issue was primarily with new pressings. - ghost of olddude55 13:54:01 04/21/21 (0)

Same one I have. - ghost of olddude55 04:06:32 04/21/21 (0)

One of my favorites.... - alan m. kafton 01:50:40 04/21/21 (0)

Interesting... had no idea there was a reaming tool... - musetap 22:18:04 04/20/21 (0)

Follow Ups

$50 for one drill bit? Now, that is over the top. The drill is very close - alaskahiatt 04/21/2122:27:29 04/21/21 (0)

Post a Message!