Thanks, Just saw it. How about the values? - Todd R

Planar Speaker Asylum

Welcome! Need support, you got it. Or share your ideas and experiences.

Follow Ups Full Thread

Topic - Zobel values for MG1.6? - s.hum 20:09:20 09/21/01 (29)

Re: Zobel values for MG1.6? - Mart 20:54:01 09/21/01 (28)

Re: Zobel values for MG1.6? Me too Mart. - Todd R 07:02:31 09/22/01 (6)

see below - Mart 07:08:56 09/22/01 (5)

Thanks, Just saw it. How about the values? - Todd R 09/22/0107:17:13 09/22/01 (4)

nope, it was for bi-wiring - Mart 07:28:30 09/22/01 (3)

Like this Mart? - Todd R 14:10:03 09/22/01 (2)

you have to use <PRE>plot</PRE> - Mart 14:50:13 09/22/01 (1)

Thanks a bunch - Todd R 15:04:17 09/22/01 (0)

Re: Zobel values for MG1.6? - s.hum 06:14:36 09/22/01 (13)

Re: Zobel values for MG1.6? - Mart 07:06:46 09/22/01 (12)

Re: Zobel values for MG1.6? - Monk 13:16:21 10/5/01 (11)

as initially designed yes - Mart 13:39:55 10/5/01 (10)

Re: as initially designed yes - Monk 13:52:31 10/6/01 (9)

to make a long story short ... - Mart 08:59:49 10/7/01 (8)

Re: to make a long story short ... - monk1 12:23:23 10/8/01 (7)

attenuation in RF region - Mart 22:37:19 10/8/01 (6)

Re: attenuation in RF region - Monk1 11:01:51 10/9/01 (5)

1mm penetration is a 1D model - Mart 11:34:36 10/9/01 (4)

Re: Skin depth - Monk1 14:04:04 10/9/01 (3)

Re: Skin depth - Mart 14:55:10 10/9/01 (2)

Re: Transmission lines - Monk1 15:42:42 10/9/01 (1)

just substituted a long cable length - Mart 00:42:58 10/23/01 (0)

Some clarification needed... - s.hum 06:05:27 09/22/01 (6)

Re: Some clarification needed... - Mart 06:52:40 09/22/01 (5)

Great! - s.hum 07:35:48 09/22/01 (4)

should re-emphisize - Mart 07:50:27 09/22/01 (3)

Network location - s.hum 08:21:12 09/22/01 (2)

across the speaker terminals - Mart 08:36:10 09/22/01 (1)

Driver inductance. - Arbelos 15:19:46 09/23/01 (0)

Follow Ups

Thanks, Just saw it. How about the values? - Todd R 09/22/0107:17:13 09/22/01 (4)

nope, it was for bi-wiring - Mart 07:28:30 09/22/01 (3)

Like this Mart? - Todd R 14:10:03 09/22/01 (2)

you have to use <PRE>plot</PRE> - Mart 14:50:13 09/22/01 (1)

Thanks a bunch - Todd R 15:04:17 09/22/01 (0)