|
Tube DIY Asylum: So far two that should fit... by restock Do It Yourself (DIY) paradise for tube and SET project builders. |
For Sale Ads |
136.159.58.135
In Reply to: Stepped attenuator with low profile for Fi Y pre? posted by restock on January 11, 2006 at 17:25:53:
Leaving all high gain problems aside, I am wondering whether I can at least "gain" (pun intended) some quality and improve on the standard pot.The current pot tracks to about 0.5dB through most of the range, not stellar, but o.k. The question is can I improve on that?
Two attenuators that are less than 25 mm deep I found are:
- ALPS Blue Velvet (3.0dB)
- TKD CP-601 (about 0.6 to 2dB tracking dependent on attenuation level)Looking at the tracking number I think either one will only be a slight or no improvement for channel tracking. Anyone out there with experiences for the two pots? Is there any other sonic benefit using one of these two?
Thanks again for everyone's help.
Rene
"I wouldn't trust (no) words written on no piece of paper."
Jim Jarmusch, DEAD MAN 1995
This post is made possible by the generous support of people like you and our sponsors:
Topic - Stepped attenuator with low profile for Fi Y pre? - restock 17:25:53 01/11/06 ( 27)
- I trust you know two inputs have reduced gain for use with high output sources(nt) - Russ57 07:44:04 01/13/06 ( 1)
- Yep... - restock 10:30:36 01/13/06 ( 0)
Re: Stepped attenuator with low profile for Fi Y pre? - Dave Cigna 16:06:34 01/12/06 ( 1)
- Re: Stepped attenuator with low profile for Fi Y pre? - restock 10:43:34 01/13/06 ( 0)
So far two that should fit... - restock 01/12/06 12:52:01 01/12/06 ( 0)
You might try a law faked linear (Vishay/Sfernice cermet)(nt) - Russ57 12:14:16 01/12/06 ( 1)
- Completely agree with Russ - law faking - andy evans 14:30:55 01/12/06 ( 0)
Measuring the tracking differences... - restock 23:10:32 01/11/06 ( 5)
- Re: Measuring the tracking differences... - fatbottle 05:00:52 01/12/06 ( 4)
- To refresh yr memory... - cheap-Jack 07:36:11 01/12/06 ( 3)
- I must apologise for this , I'm being stalked by Cheap Jack.... - fatbottle 07:40:14 01/12/06 ( 2)
- Sorry, c-J stalked you, again ! - cheap-Jack 07:56:32 01/12/06 ( 1)
Re: Stepped attenuator with low profile for Fi Y pre? - dave slagle 18:28:40 01/11/06 ( 13)
- Re: Stepped attenuator with low profile for Fi Y pre? - restock 18:45:00 01/11/06 ( 12)
- Get to the root of the problem - too much gain. - cheap-Jack 09:18:17 01/12/06 ( 0)
- Re: Stepped attenuator with low profile for Fi Y pre? - dave slagle 19:09:59 01/11/06 ( 2)
- YES ! - cheap-Jack 07:47:33 01/12/06 ( 0)
- Re: Stepped attenuator with low profile for Fi Y pre? - restock 20:57:09 01/11/06 ( 0)
Re: Stepped attenuator with low profile for Fi Y pre? - GEO 19:00:43 01/11/06 ( 7)
- Re: Stepped attenuator with low profile for Fi Y pre? - restock 21:05:14 01/11/06 ( 3)
- Re: Stepped attenuator with low profile for Fi Y pre? - GEO 05:53:02 01/12/06 ( 2)
- Re: Stepped attenuator with low profile for Fi Y pre? - restock 08:25:49 01/12/06 ( 1)
- Re: Stepped attenuator with low profile for Fi Y pre? - kyle 12:58:07 01/12/06 ( 0)
Re: Stepped attenuator with low profile for Fi Y pre? - restock 21:02:26 01/11/06 ( 0)
Re: Stepped attenuator with low profile for Fi Y pre? - dave slagle 20:38:40 01/11/06 ( 1)
- Re: Stepped attenuator with low profile for Fi Y pre? - GEO 05:51:17 01/12/06 ( 0)